Steamboat Scanoe Steamboat - Steamboat Register Radow sorted by Boiler

Steamboat Register Radow sorted by Boiler


Flaming Galah
Flaming Galah = vorherige Seite
Übersicht
Dory - 1999 = nächste Seite
Dory - 1999
metric/imperial
metric
imperial

Steamboat Scanoe Steamboat

nation:  
Nation: USA
14.02.2005

length
4.70 m
15'-5"
beam
1.04 m
3'-5"
engine:
50.8 x 38.1
2" x 1 1/2"
boiler: Flash Steam

Steamboat Scanoe Steamboat - Picture 1
Picture 1
15.5 ft x 3.5 ft square stern canoe, plastic hull. 4 mph (6.5 kph)

Figuring out how to unload and setup a steamer from a cartop mounting was a challenge. I made sure any individual component would not require more than 50 pounds (23 Kg) lifting.

Steamboat Scanoe Steamboat - Picture 2

Picture 2
The bare hull had a weight of 110 pounds, 50 pounds at the bow, and 60 pounds at the stern. The boat slides off the car, being balanced midway on the cartop, so it is easy to lower the rear wheels to the ground, holding up less than 50 pounds weight (just enough for an old man like me). Then I would get under the inverted bow, still perched on the cartop, and lower the bow to the ground, 50 pounds again

Steamboat Scanoe Steamboat - Picture 3
Picture 3
After releasing the rear wheel set pin, allowing hull rotation to place the bare hull upright, and attaching the midship wheel set, I had a boat that could be rolled up to the tailgate of the car. Heights were set so that the boat sheer line and the tailgate were at the same elevation.

Steamboat Scanoe Steamboat - Picture 4
Picture 4
Needless to say, all of this is much more work than a simple small boat trailer.

The steam plant, (boiler, engine, pumps, and feedwater heater, feed filters) were all mounted on a single sheet of plywood, again about 100 pounds. This would slide off the car tailgate, and onto one of the cross member beams of the boat, really very little effort. Then I would tilt the steam plant and slide it into the hull, for attachment with "U" bolt type latches. Always less than 50 pounds to handle.

Steamboat Scanoe Steamboat - Picture 5

Picture 5


Steamboat Scanoe Steamboat - Picture 6
Picture 6


Steamboat Scanoe Steamboat - Picture 7
Picture 7
After attaching all the other items (Propane tank, feedwater tank, about 10 gallon jugs of pure feedwater, lunch, anchor, etc.) I could easily roll the unit directly into the water with no problems. The entire assembly weighed about 350 pounds (160 Kg) without passenger, and most of the weight was on the forward wheel set, so the stern could easily be lifted to point the boat in any desired rolling direction. The rear wheel set protected the propeller drive unit during launching

Steamboat Scanoe Steamboat - Picture 8
Picture 8
After launching, the wheels (front and rear) would be removed, although the boat could be run with them in place if the underwater conditions were unknown.

Steamboat Scanoe Steamboat - Picture 9
Picture 9
Inboard/Outboard drive, made from Eska outboard lower unit. 8 inch x 8 inch propeller, 1000 RPM

Steamboat Scanoe Steamboat - Picture 10
Picture 10


Steamboat Scanoe Steamboat - Picture 11
Picture 11
Coming out of the water was difficult for one person, when I could not find a helper, I would unload the fuel and water tanks, plus other ancillaries at the dock, to allow myself to roll the hull ashore. On one occasion I pulled the entire boat assembly out of the water with the car, but I had to tow it to a fairly level part of the parking lot.

Steamboat Scanoe Steamboat - Picture 12
Picture 12
Steam Engine 2 inch bore x 1.5 inch stroke, 600 RPM, single acting, made from 4.7 cubic inch chain saw engine.



Steamboat Scanoe Steamboat - Picture 13
Picture 13
Monotube Boiler, 5 square ft heating surface, 1/4 inch OD x 0.035 wall type 304 stainless steel tubing. 160 psig operating pressure, 5000 psi design pressure.
Propane Firing.

Steamboat Scanoe Steamboat - Picture 14
Picture 14
Here is a short MPG film of the little steamer on the lake(size = 1,4 MB, if not play direct, save with right click and "save as" and open in your media player by hand..) . All of the steamboats in our group glide silently and majestically through the water, but the little Cartop Boat sounds like a steam locomotive! This is because I had a steam exhaust into the stack, to give draft to the fire, the same as a locomotive.

If you look at the steam pressure gauge you will see that steam pressure jumps between 120 and 140 psig (8.3 to 9.6 bar) on every engine stroke. This is because there is no large steam reservoir in the system. Power control had to be by use of the propane burner control, which was entirely satisfactory, as long as the fuel source is readily controllable. The flash steam plant is not so suitable to wood or solid fuel firing. If I shutoff steam to the engine with the burner on, the safety valve (175 psig, 12 bar) would lift in a fraction of a second, blow steam and reseat. This would repeat at about 10 times a second, sounding like a machine gun.

Steamboat Scanoe Steamboat - Picture 15

Picture 15


First release of this page: 14.02.2005. 

Flaming Galah
Flaming Galah = vorherige Seite
Übersicht
Dory - 1999 = nächste Seite
Dory - 1999